Skip to the installation guide
Free Standard Shipping on Eligible Orders Over $50
Cart
CORNHOLE CONNECTION / INSTALLATION GUIDE

A smooth install.
A game-ready finish.

Give your new board wraps the professional finish they deserve. Follow this straightforward, illustrated guide for preparation, alignment, application, trimming, and care.

View the steps ↓
Dry installation onlyAll 3 board sizes8 easy steps
BEFORE YOU BEGIN

Gather a few simple tools.

A clean workspace and the right supplies make installation easier. Work indoors or in a sheltered, dust-free area at a comfortable room temperature.

Felt-edge squeegee
Painter’s tape
Sharp craft knife
Alcohol & microfiber
Hair dryer / low heat
!
Important: Do not wet-install these wraps.

Our vinyl uses air-release technology and is designed for dry application. Never apply water, soap solution, or other wet-install liquids beneath the adhesive. A smooth, fully cured board surface is essential for a durable bond.

THE INSTALLATION PROCESS

Follow these 8 steps.

Take your time—especially during alignment and the first few squeegee passes.

STEP 01POSITION

Prepare the board

Smooth, sealed, completely dry.

Fill divots, sand the playing surface, and remove all dust. Seal or paint bare wood with a smooth, compatible gloss or semi-gloss finish. Follow the coating manufacturer's full cure time (at least 48 hours) before installation, then wipe the surface with 70–90% isopropyl alcohol and allow it to dry.

PRO TIP Avoid applying directly to raw wood, chalky paint, or textured/matte coatings.
STEP 02POSITION

Position the wrap

Check the fit before peeling.

Lay the wrap face up over your board and align the artwork with the outside edges and center hole. Confirm the wrap matches your board size—Standard, Tailgate, or Mini—and make any adjustments before exposing the adhesive.

PRO TIP A second set of hands is helpful for larger wraps.
STEP 03POSITION

Create a tape hinge

Keep everything aligned.

With the graphic in position, place a strip of painter's or masking tape across the middle of the wrap and onto the board. This acts as a hinge so the design cannot shift while you begin applying it.

PRO TIP Use enough tape to keep the graphic secure without stretching it.
STEP 04APPLY

Expose the first half

Peel the liner, not the artwork.

Fold one half of the wrap back over the tape hinge. Slowly separate the white backing paper from the adhesive side, stopping at the tape. Cut away the exposed backing paper carefully, keeping the adhesive off the work surface.

PRO TIP Never remove the entire backing paper at once.
STEP 05APPLY

Squeegee from the center

Apply with overlapping strokes.

Lay the exposed vinyl onto the board gradually. Starting at the center hinge, use a felt-edge squeegee with firm, even pressure, working toward the outer edge. Overlap each stroke to push trapped air outward.

PRO TIP Work slowly and keep the loose adhesive from touching down ahead of your squeegee.
STEP 06APPLY

Finish the second half

Repeat the same technique.

Remove the tape hinge, fold back the remaining unapplied section, and peel away its backing paper a little at a time. Continue squeegeeing from the center toward the end until the graphic is fully adhered. Check the surface for any lifted areas.

PRO TIP For small bubbles, gently work them toward the nearest edge rather than forcing or stretching the vinyl.
STEP 07FINISH

Trim the edges and hole

Use a fresh, sharp blade.

Carefully trim the vinyl approximately ⅛ inch inside the outside perimeter to help prevent edge lifting. Cut out the center hole neatly, following the opening without gouging the board. Keep your fingers clear and cut away from your body.

PRO TIP An overhanging lip can catch on bags and begin peeling.
STEP 08FINISH

Set the edges & protect

A little attention goes a long way.

Gently warm the trimmed perimeter and the edge of the center hole with a hair dryer or a heat gun on a low setting, then press firmly with a squeegee or soft cloth. For additional protection, you may seal the exposed edge with a thin application of vinyl-compatible, water-based clear coat after testing in an inconspicuous area.

PRO TIP Do not overheat the vinyl. Edge sealing is optional, not a required full-surface clear coat.
AFTER INSTALLATION

Keep your boards looking their best.

  • Wipe the surface with a soft, damp cloth. Avoid abrasive scrubbers and harsh cleaners.
  • Store boards indoors in a clean, dry place when not in use.
  • Do not leave boards outside for extended periods. Moisture can warp the wood and compromise adhesion.
  • Check the edges periodically, especially around the center hole.
A NOTE ON CLEAR COAT

Do you need to seal the wrap?

For laminated wraps, a full-surface clear coat is generally unnecessary. A thin, compatible water-based clear coat along the trimmed edges is an optional way to add protection. Test compatibility first and avoid flooding the adhesive edge.

If your wrap is unlaminated, ask us about appropriate protective finishing before applying a coating.

COMMON QUESTIONS

Good to know.

Can I use water or a spray application solution?

No. These wraps are designed for dry installation. Liquids under the vinyl may interfere with the adhesive and cause lifting.

What if I see a small air bubble?

Use your felt-edge squeegee to move the trapped air slowly toward the nearest edge. Avoid lifting and reapplying large areas, and don't stretch the vinyl.

Can I apply a wrap directly to unfinished plywood?

We recommend against it. Fill, sand, and seal or paint the board with a smooth, wrap-compatible finish, and allow the coating to cure fully before applying the vinyl.

Will this method work for Mini or Tailgate wraps?

Yes. The dry tape-hinge technique is the same for Standard (24 × 48 in), Tailgate (24 × 36 in), and Mini (12 × 24 in) wraps. Match the wrap size to your actual board dimensions before installing.

NEED A HAND?

We're happy to help.

Questions about board prep, finishes, or installation? Get in touch before applying your wrap.

Contact Cornhole Connection